英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

vaporizable    
a. 蒸发的;汽化的

蒸发的;汽化的

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • LIN Physical Layer - Developer Help - Microchip Technology
    The LIN bus operates between 9 V and 18 V Typically, the microcontroller LIN I O pins voltage levels are adjusted to the LIN bus levels by a transceiver This allows the microcontroller to operate at 3 5 V levels, while the bus operates at higher levels
  • LIN Bus Explained - A Simple Intro [2025] - CSS Electronics
    Every LIN node is connected to the single wire LIN bus (LIN), the supply voltage (VBAT) and a shared ground (GND) LIN allows for 12V and 24V systems across a max bus length of 40 meters with bit-rates of 1 to 20 kbit s (typically 9 6, 10 4 or 19 2 kbit s)
  • Exploring the LIN bus with an oscilloscope - Test and Measurement tips
    In looking at LIN Bus signals on a scope, the lower level voltage (logic zero) should be less than 20% of battery voltage (typically 1 V) and the upper level voltage (logic one) should be more than 80% of battery voltage The voltage levels may change slightly when the engine is started
  • Automotive Communication Networks, Part I LIN Bus - Snap-on
    For a recessive bit, the LIN voltage must be greater than 80% of the battery voltage For a dominant bit, the LIN voltage must be less than 20% of the battery voltage The slew rate or transition time between a high bit and a low bit is critical too for data transfer
  • LIN Bus Basics: Everything You Need to Know (2025) - AutoPi. io
    The standard voltage for LIN bus systems is usually around 12 volts, which is common in most automotive electrical systems This standardization helps in maintaining compatibility and reliability across different vehicle models and components
  • Models - National Highway Traffic Safety Administration
    Note: The LIN Bus voltage never goes to fully system voltage or to ground A properly operating LIN Bus voltage should be approximately 1 volt less than system voltage and 1 volt above ground, as shown
  • LIN Bus Diagnosis - Diagnostic Network
    Testing for power on the switch input indicates there is sufficient voltage available Testing the power feed to the motor indicates there is also sufficient voltage available Testing grounds at the motor and switch to battery voltage with a test light and meter indicates a solid ground diag net file f40qfr8p5… diag net file f2qg0xt6w…
  • Introduction to the LIN bus - Kvaser
    Voltage supply (Vsup) for an ECU should be between 7 V and 18 V The limits for how the level of the bus is interpreted are shown in figure 2 Figure 2: Determination of the logical level on the bus The LIN network is described by a LDF (LIN Description File) which contains information about frames and signals
  • LIN Bus Basics for Beginners - Lipowsky
    The LIN transceiver translates the logic levels of the microcontroller (typ 3 5V) into the LIN voltage range (8 18V) and converts the full- duplex RXD TXD interface into a 1-wire half-duplex interface
  • LIN Protocol and Physical Layer Requirements (Rev. A) - Texas Instruments
    The LIN protocol specification describes the physical and data link layers, and the LIN Configuration Language enables the LIN cluster to be described in a file that is straightforward for any developer





中文字典-英文字典  2005-2009