英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

nubbin    
n. 小瘤,小片,玉蜀黍发育不良的穗

小瘤,小片,玉蜀黍发育不良的穗

nubbin
n 1: a small nub (especially an undeveloped fruit or ear of
corn)

Nubbin \Nub"bin\, n.
A small or imperfect ear of maize. [Colloq. U. S.]
[1913 Webster]


请选择你想看的字典辞典：
单词字典翻译
nubbin查看　nubbin　在百度字典中的解释百度英翻中〔查看〕
nubbin查看　nubbin　在Google字典中的解释Google英翻中〔查看〕
nubbin查看　nubbin　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Effective Gasket Width in ASME VIII-1 App2 Calcs | Eng-Tips
    Hello there I am trying to do the calculations in ASME VIII-1 App 2, however, I do not understand how to calculate "N" (based upon the possible contact width of the gasket) On what aspect of the gasket do we base it : the sealing element of the gasket or the actual surface contact of the
  • Nubbins | Eng-Tips
    The conclusion was flanges without nubbin sealed better and the cost of machining off the nubbin is justified by the increase in sealing efficiency
  • Nubbin on a Body Flange | Eng-Tips
    What drives the requirement for a Nubbin on a Heat Exchanger Shell Flange?
  • Nubbin | Eng-Tips
    A nubbin is just a small tooth obtained by machining on the joint contact area of a flange This is a very detailed issue and is normally specified by joint manufacturers for use with specific types of joints
  • Tema Type R, confined gaskets, and nubbins | Eng-Tips
    TEMA allows the use of any desired facing, including the described nubbin I generally avoid them except with flat metal gaskets, but that's personal preference
  • Appendix 2 Flange Calculations with Nubbins | Eng-Tips
    Two existing girth flanges are mated together One flange has a nubbin 1 64” high and 1 8” wide The gasket used between the flanges is DJAF iron, that is 1 2” wide Question: When considering the facing on the flanges as Type 2 (per Table 2-5 2, from Sec VIII, Div 1, Appendix 2), the joint
  • ASME B16. 5 Class 600 Flange Face - Min Raised Face? | Eng-Tips
    I've been asked to design a flanged joint using a pure copper gasket to seal Fluorine gas at 1000 PSI I looked at ASME b16 5 and thought that a class 600 raised face design would work, but couldn't understand what the minimum thickness (width) of the raised face could be I wanted to I use
  • Specify tongue and groove gasket seating width | Eng-Tips
    What the Code calls a nubbin, a narrow raised area on the flange gasket seating face, is often used with flat solid metal gaskets to reduce the seating load and required bolting The Nmin calculation is not part of the Code, but some handbooks, specifications, and software perform it and select the N based on that
  • table 2. 5. 2 which facing sketch and column represent a . . . - Eng-Tips
    inammanj123, noting that Sketch 2 5 2 is for determining effective gasket width only, you will most likely be following Sketch 1 (a), or Sketch (2) if using a nubbin (I wouldn't unless using a solid metal gasket)
  • What ASME section covers in-service repairs and alterations?
    The in-service repairs of pressure retaining items does NOT fall under ASME Boiler and Pressure Vessel (B PV) ASME B PV Code is a construction code, not an in-service inspection or repair code In -service inspection, repair and alteration activities are either governed by API (petrochemical) or by the National Board Inspection Code (NBIC) NB-23 You should first determine what the





中文字典-英文字典  2005-2009