英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • MP35N Strain Hardened Ground AMS 5844 3 - Eng-Tips
    We purchased the material to AMS 5844 In your reply you state that the AMS 5844 is solution annealed and worked harden and is that the standard In order to form this, we actually took bar stock and machined it to flat plate to wire edm a flat band that is 200 wide and 044 thick and 17 inches long
  • cam material with good wear and corrosion resistance
    It is commonly used in the medical industry With the proper coditioning, hardnesses of RC 55 can be achieved, with good ductility, and superior corrosion resistance, compared with 400 series martinsitic stainless steel See AMS 5844 and AMS 5845
  • High Temperature High Strength Alloy - Boiler and Pressure Vessel . . .
    AMS 5844 AMS 5845 ANSI ASTM F562 Upvote 0 Downvote Jun 23, 2004; Thread starter #9 jmoon Mechanical
  • AMS 2700: Which Type with Which Grade? 6 - Eng-Tips
    That table and guidance is not contained in the AMS 2700 document (which the SAE has identified as superseding AMS-QQ-P-35 in it's February 2005 cancellation of AMS-QQ-P-35), nor is the QQ-P-35 AMS-QQ-P-35 Type I callout included in the cross reference table included in the AMS-QQ-P-35 to AMS 2700 Type "Cross Reference" Table found on the
  • Looking for the AMS equivalent of ASTM B221 (6061-T6)
    I'm reading ASTM B221 right now, and it's not equivalent to AMS 4150 But it might not be inferior, either ASTM B221 is titled " Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes" , which is pretty broad, and lists dozens of candidate materials suitable for extrusion according to this process
  • Aluminum 6061-T6 per AMS-QQ-A-250 11 (plate) versus 6061-T6 . . . - Eng-Tips
    First, AMS QQ-A-250 11 has been canceled as of 2008 It has for 6061-T6 been superseded by AMS 4027 My
  • amp readings? - Pump engineering | Eng-Tips
    here's the story, the plumbers in the building maint department say there is a clog in the 8inch pipe down the line from the discharge well when the pump runs,after about 30mins, it heats up and the amp reading are 6 4amps on each phase the nameplate on the motor is 9 5amps on a 480volt connection
  • 15-5 PH Condition 1025 Heat Treat Per AMS 2759 3
    An additional requirement was to heat treat to condition H1025 per AMS 2759 I purchased material from the Mill as Cond 1025H but was not certified to AMS2759 for the heat treat The Mill says that his Condition H1025 is for unfinished bar and that final Heat Treat to condition H1025 per AMS 2759 3 should be accomplished by us since we are
  • Glass weave style numbers, 120, 7781, etc. 2 - Eng-Tips
    MIL-C-9084 (now superseded by AMS-C-9084) defined many weave styles, itemized by typical MIL classifications (Type Class), and identified (for reference) the commercial designations The commercial designations were flag noted: "Commercial designations are nominal weights per square yard are shown for information only and are not requirements
  • before or after plating dimensions | Eng-Tips
    Some companies use the term "coating" or "finish" as in "Dimensions apply after coating" Thus it covers all, including paint





中文字典-英文字典  2005-2009