英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Need Help! DMU 50 setup help - CNCzone
    I'm absolutely new to the DMG Mori, DMU 50 Ours is 2015 year and has Siemens controls with the Celos Ergoline touchscreen control, 5 axis monoblock (n
  • Mazak Quickturn, Mazatrol T Plus, shuts sometimes down, Alarm . . . - CNCzone
    If this is your first visit, be sure to check out the FAQ by clicking the link above You may have to register before you can post: click the register link above to proceed To start viewing messages, select the forum that you want to visit from the selection below
  • G76 Two Line Threading - cnczone. com
    I could use some help I am reviewing our shops G76 Canned Thread Cycles Out of my curiosity I have stumbled upon a few good questions Standard two l
  • Axis drifting. Need some help.
    Yeah, seems like the problem followed the driver I didn't swap any cables, just the drives within the g540 (moved z to y) Unfortunately, my setup uses 2 drives for the gantry (x axis) so I don't have a spare Was thinking of just buying a spare g250x but thought there may be some benefit to sending the entire g540 back to gecko
  • M-Code List for PUMA Lathe - CNCzone
    The table below shows M-codes that apply for most PUMA models manufactured from year 1998 and up Gantry-loader models are not included in this list Actual availability of the M-codes as shown may vary, depending on machine type and optional equipment furnished
  • Toolpath creation problem - CNCzone
    When i try to generate a toolpath ( outside right) for the outline (please look at the attached drawing) I get this error: No toolpath generated for c
  • Re-cut threads and canned cycles - CNCzone
    Short answer is yes, you can recut rerun the thread program if you don't take out the part I had the same exact concern when the test nut didn't fit I even cut and pasted just the thread code on a new file and it ran just fine I also noticed that path pilot leaves a bit too much material after threading and I would have to recut chase the threads often But I wouldn't be surprised if I
  • Chuck Unclamp alarm - CNCzone
    I fixed it! I had to adjust the prox sensors for the chuck clamping here's the answer for anyone who encounters this problem found it on reddit: Take a look at the two prox sensors at the back of the draw tube (there's an access panel you remove if it's still there) Sensor on the left should be lit up for OD clamping, on the right for ID clamping Only one can be lit at a time- if both are
  • How do I adjust backlash compensation? - CNCzone
    little bubba, thanks for the reply I looked at the machine today, its a extremely clean machine and everything worked nicely I've looked at many machines over the past couple of years and I have never seen a used machine that was kept so clean With the backlash compensation set to zero the Z axis had 0004, the X had 0015, and the Y had 0065 of backlash obviously their is something other
  • Containers for chip coolant recovery - cnczone. com
    Hi, I am looking for suggestions on what to use as chip coolant recovery bins to use under our Haas chip conveyors We currently use 2 plastic bins We





中文字典-英文字典  2005-2009